Lumitek Opal White Glass Smart LED Floor Lamp with Touch Dimmer

Overview:

Osram LED T8 SubstiTUBE Value 5ft in 4000K (840) for EMag/Mains, is an economic LED tube for electromagnetic control gears or direct wire to Mains. A quick, simple and safe replacement without rewiring (comes with jumper starter), offering energy savings of up to 65% (compared to T8 fluorescent lamp on CCG), with a wide 220 beam angle, and luminous efficiency up to 105 lm/W. These tubes provide Instant-on light, therefore ideally suitable in combination with sensor technology. Very high resistance to switching loads. Also suitable for operation at low temperatures (from -20 to 45). Not suitable for operation with electronic/HF control gear.

Overview:

Finish: Rustic painting
Item Type: European Crystal wall lamp
Light Source: LED E14/E12 bulbs, Energy Saving
Main materials: Iron and crystal
Material: Iron
Voltage: 110-240V

Overview:

Areas of Application: Office, indoor, school, mark etc.
Lamp Body Material: Iron
Warranty (Years): 2

Specifications:

Cap base: G13 (Medium Bi-Pin Fluorescent)
EU RoHS compliant: Yes
Nominal lifetime (nom.): 15000h
Switching cycle: 50,000X

Overview:

Osram LED T8 SubstiTUBE Value 4ft in 6500K (865) for EMag/Mains, is an economic LED tube for electromagnetic control gears or direct wire to Mains. A quick, simple and safe replacement without rewiring (comes with jumper starter), offering energy savings of up to 65% (compared to T8 fluorescent lamp on CCG), with a wide 220 beam angle, and luminous efficiency up to 105 lm/W. These tubes provide Instant-on light, therefore ideally suitable in combination with sensor technology. Very high resistance to switching loads. Also suitable for operation at low temperatures (from -20 to 45). Not suitable for operation with electronic/HF control gear.

Specifications:

Cap-Base: G5 (G5)
EU RoHS compliant: Yes
Nominal Lifetime (Nom): 50000h
Switching cycle: 50000X

Overview:

Areas of Application: Office, indoor, school, mark
Lamp Body Material: Iron
Warranty (Years): 2

This is a Osram LEDvance 5ft 1500mm 19.1w LED T8 Tube with a frosted finish.
These tubes are a direct retrofit for old 58w T8 or 65w T12 fluorescent tubes in switch start fittings as they come complete with a Free LED Starter. All you need to do is simply remove the old tube and starter and replace with the LED tube and starter supplied. They can also be used in high frequency fittings, by bypassing the control gear and wiring the fitting live and neutral to one end only.

This is a Osram LEDvance 2ft 7.6w LED T8 Tube with a frosted finish.
These tubes are a direct retrofit for old 18w T8 or 20w T12 fluorescent tubes in switch start fittings as they come complete with a Free LED Starter. All you need to do is simply remove the old tube and starter and replace with the LED tube and starter supplied. They can also be used in high frequency fittings, by bypassing the control gear and wiring the fitting live and neutral to one end only.

Overview:

Areas of Application: Living Room, Restaurant, Lobby, Hotel, Loft, Club, Restaurant
Certification: CCC, CE, RoHS, SAA, FCC
Color Rendering Index – CRI (Ra>): 80
Color Temperature (CCT): 4100K (Neutral White)
Color: Gold
Input Voltage (V): 110-240
Is dimmer supported? No
Item Type: Modern Wall Lamp
Lamp Body Material: Crystal
Lamp Luminous Flux (lm): 1200
LED Light Source: G4, G9, E14, or E27
Lifespan (hours): 30000
Light Source: Energy Saving
Lighting Solution Services Available: Project Installation. (For these additional services, please fill in the Inquire Form below to get assistance and the best quote)
Shade Material: Crystal
Warranty (Year): 1-Year
Working Lifetime (Hour): 20000
Working Time (hours): 30000

Overview:

Certification: CE, RoHS
Finish: Gold
Item Type: European Bedroom Wall Lamp
Light Source: LED E14/E12 x 2, Energy Saving
Material: Iron and fabric
Shade Color: White or black
Voltage: 110-240V

This is a Osram LEDvance 4ft 1200mm 16.4w LED T8 Tube with a frosted finish.
These tubes are a direct retrofit for old 36w T8 or 40w T12 fluorescent tubes in switch start fittings as they come complete with a Free LED Starter. All you need to do is simply remove the old tube and starter and replace with the LED tube and starter supplied. They can also be used in high frequency fittings, by bypassing the control gear and wiring the fitting live and neutral to one end only.